Ghost 2 Immobiliser Reviews

The ghost 2 immobiliser is an innovative anti-theft device that makes use of modern technology to ward off car theft. The device is hidden by thieves and only turns on the engine after a PIN or app is entered.

It's weatherproof and connects to the CAN data network of your vehicle. It also comes with the service/valet mode that allows you to start your car temporarily while it's in garage for servicing or cleaning.

Easy to install

The Ghost immobiliser shields your car from key theft as well as hacking, cloning and stealing. It uses a unique PIN code system that is incorporated into the car's ECU, making it difficult for thieves to detect or tamper with. In contrast to traditional immobilisers, it doesn't require special keys or sensors and is completely hidden without any LED indicators or signals that signal its presence. It's also cheaper than replacing an ECU, or installing a key fob. It can even lower the cost of insurance.

Follow the directions of the manufacturer when installing a Ghost 2 vehicle immobiliser. This will ensure that the device operates efficiently and correctly. After the installation is complete, test the system by entering the PIN code, then turning on the engine. Regular testing will enable you to spot any issues early.

Before beginning the installation, make sure you check the exact location of the CAN H and L wires. They are vital for ghost 2 immobiliser Reviews powering the immobiliser, therefore it is crucial that they are connected properly. Labelling the wires will make it easier to find them when installing. Once you've identified the locations of these wires, connect them to a constant 12V power source as well as the grounding point. Use the fuse tap to safeguard the connections against damage or short-circuits.

After connecting the wires, tidy the wiring with cable ties to avoid potential alteration. It is also a good idea to cover the wires with insulation tape or heat shrink tubing. This will help protect them from electrical shorts and extend the life span of the device. It is a good idea to test your Ghost 2 immobiliser once the wiring is secure.

The Ghost 2 immobiliser offers a service mode for situations in which you may have to give your vehicle away, such as when it is being serviced or valet-parked. This will disable the PIN sequence temporarily. To activate this feature, simply press the brake pedal while holding down the accelerator, and press a number of times that is equal to the first number of the emergency code. The system will then go into service mode, which can be confirmed by flashing the indication signal five times.

It is simple to change PIN codes

It is simple to secure your vehicle from theft with a ghost 2 immobiliser. It is discreetly installed inside the vehicle and can only be accessed by a unique code. The device communicates directly with the vehicle ECU through its data bus. It does not use radio frequency signals, as do traditional Thatcham immobilisers or aftermarket alarm systems. This makes it more difficult for thieves to hear the click of an immobiliser relay, or add new keys. The control unit is concealed within the vehicle's wiring harness or dashboard and cannot be physically tampered with to reset the system.

The ghost vehicle immobiliser 2 immobiliser what is a ghost immobiliser connected to your vehicle's CAN Data network and utilizes the buttons already present on the steering wheel, door panels, and the centre console to create a customisable sequence of up 20 button presses that must be entered prior to the engine starts similar to the PIN code. This next-generation system does not require any wire cutting upon installation and can be reprogrammed at anytime. You can even start your vehicle in Valet or Service mode when you give it to a mechanic complete the work.

You can also make use of the app to change your PIN code or disable it completely if lost your keys. This feature is particularly useful if you have given your vehicle to someone else for valet parking or servicing because it prevents them from starting your car and taking away without your permission. It's also inaccessible to professional thieves since it doesn't make use of circuit cuts or radio frequencies.

Another great feature of the ghost 2 immobiliser is its ability to prevent relay thefts. Relay theft is one of the most popular methods of car theft. Criminals gain access to your car's diagnostic ports, then alter the signal sent by the car's ECU to trick it into believing that a valid car key is present. The immobiliser of the traditional model is able to be bypassed this way, but with the ghost 2 immobiliser the signal is blocked by the immobiliser before it reaches the ECU.

Simple to use app

Ghost 2 is a revolutionary immobiliser that protects your car from hacking, key-cloning and key theft. It connects to the CAN data network of your vehicle and requires the use of a PIN number to start the engine. It also prevents thieves by using signal spoofing or device spoofing, which are both common tactics to steal vehicles.

The system is easy to use and functions similar to a standard car alarm. Installing the system allows you to create a unique 20-digit PIN code that must be entered prior to starting the vehicle. This will protect the vehicle from being stolen even if your keys get stolen. You can turn off the system by downloading an app for your phone.

The ghost is silent, and it does not emit radio frequency signals. It is a weatherproof and discreet device that can be installed in any vehicle. It can be concealed under the dashboard, steering wheel or door panels. It communicates with your ECU via the CAN data circuit and is not affected by diagnostic tools, which some thieves use to identify security systems. It is also not affected by jamming devices that spoof codes.

It is a covert system that can be used to prevent theft from all vehicles. Its technology has been proven be efficient and is in line with TASSA standards. The Ghost is a good choice for classic or sports automobiles. It can also be used as a method to safeguard vehicles hired on websites like Turo.

The autowatch ghost 2 immobiliser ghost vehicle immobiliser 2 represents the next generation of vehicle immobilisers. This system is undetectable to thieves and stops them from starting your car until they have your PIN or are authorised by the app. It doesn't emit radio frequencies or any other signals scanners could detect. The installation process is easy and quick. The app is user-friendly with a simple interface and a simple navigation. It also comes with a GPS tracker that can help police locate and locate the vehicle.

Simple to reset

It is possible to secure your vehicle from theft using an immobiliser that is ghost 2. It integrates into your vehicle's ECU creating a wall that thieves are unable to penetrate without the right pin. It's also TASSA-certified which means it's recognized by insurance companies. It is a powerful tool to prevent car theft and could save you money in the long run.

Contrary to traditional alarms/immobilisers which require circuit cutting and Ghost 2 Immobiliser Reviews circuit cutting, the Ghost system is connected directly to the vehicle's CAN network and works using the buttons you already have on the dashboard and steering wheel. You can create a unique pin that is up 20 presses in length. This PIN is required to be entered before the engine can start like a credit card PIN. The Ghost system is completely inaccessible to thieves, and there are no LEDs to signal its presence. This makes it the most efficient aftermarket CAN-bus immobiliser available today.

The Ghost system has another benefit that it does not transmit radio frequency signals. This means it cannot be detected by thieves or snatched up. This stops key attacks that replicate and relay attacks, as well as the usual method of hacking into a car's computer system using its CAN bus by scanning for signals. In addition to this, the Ghost system is designed to be completely hidden inside the vehicle, and there are no lights or signals that indicate its presence.

The system also comes with an option for a Transport Mode that disables the Ghost system that is helpful in situations where you need to temporarily deactivate it, such as during transportation or maintenance. This mode is less effective than Service Mode as it doesn't disable the Ghost system if you exceed 31 mph in 15 minutes.

To reset your ghost immobiliser and tracker 2 immobiliser, you'll need the emergency code, which you can obtain from your installer. It is usually hidden under a scratch-off area on the card included with your installation. You should keep this emergency code safe and keep it in a location that is secure, such as your wallet at home.